SO-101 robot arm full assembly

Build the SO-101 follower arm from the printed base through the gripper, then connect its six servos in order.

Open the procedure in 3D

Tools and parts

Tools
#0 and #1 Phillips screwdrivers.
Parts
Printed SO-101 follower-arm kit, six STS3215 servos with 1/345 gearing, servo horns, PCB and interconnect cables, and the M2 × 6 and M3 × 6 mm hardware specified in the steps.

Use the follower-arm parts and motor gearing shown here. Configure motor IDs and calibrate the assembled arm using the LeRobot SO-101 setup instructions.

Replacing only motor 6? See the SO-101 gripper servo replacement guide.

Step by step

Follow these steps in 3D

44 steps
  1. Prepare the base, parts and tools

    Place the printed base on a flat surface. Remove all support material from the printed parts before you start. You need a #0 and a #1 Phillips screwdriver. Two screw sizes are used: M2x6 to fix the servos, and M3x6 for the horns and frame parts. This guide is for the follower arm, which uses six STS3215 servos with 1/345 gearing.

  2. Put in place the first servomotor

    Put in place the first servomotor as shown. Tip: each servomotor needs its own ID (1 to 6, from the base up) before it goes into the arm, because all six share one cable bus. Set the IDs first, for example with LeRobot's motor setup command.

  3. Screw the servomotor in the Base

    Fasten servomotor 1 to the base with the 4 highlighted M2x6 screws: two from the top and two from the bottom.

  4. Put in the servomotor cover in place

    Slide the highlighted cover onto servomotor 1 from the rear until it sits flush with the base and its two side screw holes line up.

  5. Screw the cover of the servomotor

    Fasten the cover (motor holder) with the 2 highlighted M2x6 screws, one on each side, so servomotor 1 cannot move.

  6. Put in place the rotation pitch part

    Place the rotation pitch (the shoulder part) onto servomotor 1 in the orientation shown, with its screw holes lined up with the servo horns on the upper and lower sides.

  7. Screw the Rotation Pitch

    Fasten the rotation pitch to servomotor 1 with the 4 highlighted M3x6 screws on the upper side.

  8. Screw the Rotation Pitch

    Fasten the rotation pitch to servomotor 1 with the 4 highlighted M3x6 screws on the lower side.

  9. Assemble the cover of the Rotation Pitch

    Fit the highlighted cover onto the rotation pitch part so it sits flush and its edges line up with the part.

  10. Put in place the second servomotor

    Insert servomotor 2 into the rotation pitch part in the orientation shown, with its output shaft on the side where the arm will attach. Route its cable so it will not be pinched by the arm.

  11. Screw the second servomotor

    Fasten servomotor 2 into the rotation pitch with the 4 highlighted M2x6 screws.

  12. Assemble the arm

    Place the first arm (upper arm) onto servomotor 2 in the orientation shown, with its screw holes lined up with the servo horns on both sides.

  13. Screw the first set of screws

    Fasten the first highlighted set of 4 M3x6 screws to fix the arm to servomotor 2. Tighten them evenly so the arm sits flat.

  14. Screw the second set of screws

    Fasten the second highlighted set of 4 M3x6 screws on the other side of servomotor 2. The arm should now be held firmly on both sides with no play.

  15. Put in place the third servomotor

    Insert servomotor 3 into the end of the arm in the orientation shown, with its output shaft on the side where the second arm will attach. Route its cable along the arm.

  16. Screw the third servomotor

    Fasten servomotor 3 into the end of the arm with the 4 highlighted M2x6 screws.

  17. Assemble the second arm

    Place the second arm onto servomotor 3 in the orientation shown, so its screw holes line up with the servo on both sides.

  18. Screw the first set of screws

    Fasten the second arm (forearm) to servomotor 3 with the first highlighted set of 4 M3x6 screws.

  19. Screw the second set of screws

    Fasten the second highlighted set of 4 M3x6 screws on the other side to finish fixing the second arm to servomotor 3.

  20. Fit the servomotor 4 holder

    Slide the highlighted motor holder for servomotor 4 onto the end of the second arm, in the orientation shown. Servomotor 4 goes into this holder in the next step.

  21. Put in place the fourth servomotor

    Insert servomotor 4 into the end of the second arm in the orientation shown. Route its cable along the arm so it will not be pinched.

  22. Screw the fourth servomotor

    Fasten servomotor 4 in its holder with the 4 highlighted M2x6 screws.

  23. Fit the wrist bracket

    Place the wrist bracket (the wrist roll/pitch part) onto servomotor 4 in the orientation shown, with its screw holes lined up with the servo horns on both sides.

  24. Screw the wrist bracket: first side

    Fasten the wrist bracket to servomotor 4 with the 4 highlighted M3x6 screws on this side.

  25. Screw the wrist bracket: second side

    Fit the 4 highlighted M3x6 screws on the other side of the wrist bracket. The bracket should now be held firmly on servomotor 4 with no play.

  26. Put in place the fifth servomotor

    Slide servomotor 5 into the wrist bracket through its open side, in the orientation shown, with its output shaft facing the gripper end.

  27. Fit the horn on servomotor 5

    Fit the horn (washer) onto the output shaft of servomotor 5 in the orientation shown, and secure it with its M3x6 centre screw.

  28. Screw the fifth servomotor

    Fasten servomotor 5 to the wrist bracket with the 2 highlighted M2x6 screws at the front. Tighten them evenly.

  29. Put in place the lower jaw

    Place the lower (fixed) jaw onto the washer of servomotor 5 in the orientation shown, with its screw holes lined up.

  30. Screw the jaw to the washer and servomotor

    Fasten the lower jaw to the horn (washer) of servomotor 5 with the 4 highlighted M3x6 screws.

  31. Screw the jaw to the washer and servomotor

    Fit the remaining highlighted screws to finish securing the lower jaw to the washer.

  32. Put in place the nuts

    Press the two highlighted nuts into their recesses in the lower jaw so they sit flush. Do this now: they are hard to reach once servomotor 6 is in place.

  33. Put in place the sixth servomotor

    Slide servomotor 6 (the gripper motor) into the lower jaw in the orientation shown, with its output shaft on the side where the moving jaw will attach.

  34. Screw the sixth servomotor

    Fasten servomotor 6 to the lower jaw with the 4 highlighted M2x6 screws, two on each side.

  35. Put in place the upper jaw

    Place the moving (upper) jaw onto the output horn of servomotor 6 in the orientation shown.

  36. Screw the upper jaw

    Fasten the moving jaw to the servo horn with the first highlighted set of 4 M3x6 screws.

  37. Screw the upper jaw

    Fit the second set of 4 M3x6 screws on the other side to finish securing the moving jaw. Gently open and close the jaw by hand to check that it moves freely.

  38. Assemble the PCB

    Fit the servo driver board (PCB) in its place at the base as shown, with its connectors accessible for the servo cable, power and USB.

  39. Plug the first servomotor to the PCB

    Connect a 3-pin servo cable from the driver board to servomotor 1.

  40. Plug the first servomotor to the second servomotor

    Connect servomotor 1 to servomotor 2 with a 3-pin cable. The servos are daisy-chained: each has two identical ports, so either port can be used.

  41. Plug the second servomotor to the third servomotor

    Connect servomotor 2 to servomotor 3. Route the cable along the arm, leaving enough slack for the shoulder and elbow to move through their full range.

  42. Plug the third servomotor to the fourth servomotor

    Connect servomotor 3 to servomotor 4. Leave enough slack at the elbow and wrist for full movement.

  43. Plug the fourth servomotor to the fifth servomotor

    Connect servomotor 4 to servomotor 5. Leave enough slack at the wrist for full movement.

  44. Plug the fifth servomotor to the sixth servomotor

    Connect servomotor 5 to servomotor 6. Gently move each joint by hand through its full range to check that no cable is pulled or pinched. Before first use, power the board and calibrate the arm (for example with LeRobot's calibration command).

Sources and credits

Public 3D instructions by Téa on TwinWorks Community. The numbered steps follow the public procedures linked above.

Hardware design by TheRobotStudio. See the upstream documentation and Apache-2.0 license.

Updated